Course Syllabus
Module 1 | Orientation | |
---|---|---|
Orientation | ||
Unit 1 | Wolf Prerequisite Course Orientation | |
Module 2 | Groundwork | |
Groundwork | ||
Unit 1 | Service Central | |
Unit 2 | Basic Electricity and Circuits Crash Course | |
Unit 3 | Electrical Measurements | |
Unit 4 | Conductor Ampacity | |
Unit 5 | GFCI and AFCI Circuit Protection Devices | |
Unit 6 | Relays | |
Unit 7 | Basic Microwave Oven Principles | |
Unit 8 | Gas Fuel Basics | |
Unit 9 | Gas Surface Burners | |
Unit 10 | Gas Oven Burners | |
Module 3 | Case Study 1 | |
Case Study 1 | ||
Unit 1 | Case Study 1: Problem Statement | |
Unit 2 | CS1: Schematic Review and Initial Findings | |
Unit 3 | CS1: Load of Interest | |
Unit 4 | CS1: LOI Circuit Analysis | |
Unit 5 | CS1: Troubleshooting Hypothesis | |
Unit 6 | CS1: Select Electrical Measurements and Specifications | |
Unit 7 | CS1: EEPs for Electrical Measurements | |
Unit 8 | CS1: Make Electrical Measurements | |
Unit 9 | CS1: Compare Measurement Results to Specifications | |
Unit 10 | CS1: Case Study Wrap-up | |
Module 4 | Case Study 2 | |
Case Study 2 | ||
Unit 1 | Case Study 2: Problem Statement | |
Unit 2 | CS2: Schematic Review and Initial Findings | |
Unit 3 | CS2: Load of Interest | |
Unit 4 | CS2: LOI Circuit Analysis | |
Unit 5 | CS2: Troubleshooting Hypothesis | |
Unit 6 | CS2: Select Electrical Measurements and Specifications | |
Unit 7 | CS2: EEPs for Electrical Measurements | |
Unit 8 | CS2: Make Electrical Measurements | |
Unit 9 | CS2: Compare Measurement Results to Specifications | |
Unit 10 | CS2: Case Study Wrap-up | |
Module 5 | Case Study 3 | |
Case Study 3 | ||
Unit 1 | Case Study 3: Problem Statement | |
Unit 2 | CS3: Schematic Review and Initial Findings | |
Unit 3 | CS3: Load of Interest | |
Unit 4 | CS3: LOI Circuit Analysis | |
Unit 5 | CS3: Troubleshooting Hypothesis | |
Unit 6 | CS3: Select Electrical Measurements & EEPs | |
Unit 7 | CS3: Make "Electrical" Measurements & Compare with Specs | |
Unit 8 | CS3: Case Study Wrap-up | |
Module 6 | Case Study 4 | |
Case Study 4 | ||
Unit 1 | Case Study 4: Problem Statement | |
Unit 2 | CS4: Schematic Review and Initial Findings | |
Unit 3 | CS4: Load of Interest | |
Unit 4 | CS4: LOI Circuit Analysis | |
Unit 5 | CS4: Troubleshooting Hypothesis | |
Unit 6 | CS4: Select Electrical Measurements & EEPs | |
Unit 7 | CS4: Make "Electrical" Measurements & Compare with Specs | |
Unit 8 | CS4: Case Study Wrap-up | |
Module 7 | Case Study 5 | |
Case Study 5 | ||
Unit 1 | Case Study 5: Problem Statement | |
Unit 2 | CS5: Schematic Review and Initial Findings | |
Unit 3 | CS5: Load of Interest | |
Unit 4 | CS5: LOI Circuit Analysis | |
Unit 5 | CS5: Troubleshooting Hypothesis | |
Unit 6 | CS5: Select Electrical Measurements and Specifications | |
Unit 7 | CS5: EEPs for Electrical Measurements | |
Unit 8 | CS5: Make Electrical Measurements | |
Unit 9 | CS5: Compare Measurements Results to Specifications | |
Unit 10 | CS5: Case Study Wrap-up | |
Module 8 | Case Study 6 | |
Case Study 6 | ||
Unit 1 | Case Study 6: Problem Statement | |
Unit 2 | CS6: Schematic Review and Initial Findings | |
Unit 3 | CS6: Load of Interest | |
Unit 4 | CS6: LOI Circuit Analysis | |
Unit 5 | CS6: Troubleshooting Hypothesis | |
Unit 6 | CS6: Select Electrical Measurements and Specifications | |
Unit 7 | CS6: EEPs for Electrical Measurements | |
Unit 8 | CS6: Make Electrical Measurements | |
Unit 9 | CS6: Compare Measurements Results to Specifications | |
Unit 10 | CS6: Case Study Wrap-up | |
Module 9 | Conclusion | |
Course conclusion | ||
Unit 1 | Wolf Factory Training Prerequisite Course Conclusion |